Product Description
Features & Benefits
- Maximum protection against most stains
- Advanced penetrating microbond protection
- Preserves natural look of stone
- Water-based formula
- Interior and exterior tile use
Uses (Interior and Exterior Use) Countertops Backsplashes Floors Walls
Advantages Maximum protection against most stains Advanced penetrating microbond protection Preserves natural look of stone Water-based formula Interior and exterior
Recommended Surfaces: Natural stone and Masonry Surfaces such as: Honed or Textured Marble Textured or Veined Granite Limestone Bluestone Travertine Sandstone
Flagstone Quartzite Saltillo Tile Best suited for the most porous stone surfaces
Item Numbers and Packaging D14924207 – Sample 2oz (59 mL) D14924218 - Pint 16oz (473 mL), 12 units per Case, 1008 units per Pallet D14924225 - Quart 32oz (946 mL), 6 units per Case, 600 units per Pallet D14924240 - Gallon (3.8 L), 4 units per Case, 160 units per Pallet D14924259 - 5 Gallon (18.9 L), 1 units per Case, 48 units per Pallet Products Available for Sale in Canada ONLY: D15130588 - Pint 16oz (473 mL), 12 units per Case, 1008 units per Pallet D15130595 - Quart 32oz (946 mL), 6 units per Case, 600 units per Pallet D15130600 - Gallon (3.8 mL), 4 units per Case, 160 units per Pallet D15130610 - 5 Gallon (18.9 L), 1 units per Case, 48 units per Pallet
Approximate Coverage Up to 112 ft2/pint (10.4 m2/473 mL) for a single coat application Up to 225 ft2/quart (21.9 m2/946 mL) for a single coat application Up to 900 ft2/gallon (83.6 m2/3.8 L) for a single coat application Up to 4500 ft2/ 5 gallon (418 m2/18.9 L) for a single coat application.
Expected Wear Up to 5 years on interior surfaces Up to 3 years on exterior surfaces For best results, reapply annually.
Shelf Life Factory sealed containers of this product are guaranteed to be of first quality for two (2) years if stored at temperatures >50°F (10°C) and <90°F (32°C). VOC Content <400 g/L (excluding water) for EPA Purposes <20 g/L (including water) for LEED and U.S. State purposes (Low Solids Coating)
Storage and Handling Instructions Avoid prolonged exposure to vapors. Use in a well-ventilated area. Do not ingest. Avoid contact with eyes and skin. KEEP OUT OF THE REACH OF CHILDREN. Do not freeze or store above 100°F (38°C). Do not mix with other chemicals. Do not release to natural waterways.
Data Sheets are subject to change without notice. For latest revision, visit www.laticrete.com. DS-282.0-0716
Cautions Consult SDS for more safety information. Inhalation: In high concentrations, vapors may be irritating to the respiratory system. Skin contact: May cause skin irritation Eye contact: May cause eye irritation Ingestion: May cause discomfort if swallowed Keep out of reach of children.
TECHNICAL DATA
Physical Properties Form Liquid Color Pale Amber Odor Mild pH 9 – 11 Specific Gravity 1.009
Working Properties Full Cure 24 – 72 hours Surface Traffic 6 – 8 hours Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions.
INSTALLATION Surface Preparation Read entire label before using. Use only as directed. Always test in a small inconspicuous area with a 24 hour cure time to determine ease of application and desired results. Allow new grout installations to cure for a minimum of 72 hours prior to application. Make sure surface is clean and free of waxes and coatings. Sealer may be applied to damp surfaces one hour after standing water has been removed. Surface temperature should be between 50°F and 80°F (10°C and 26°C). Ensure that the area is well-ventilated during application and until the surface is dry. Keep children and pets out of the area until treated surface is dry.
Directions
1. Ensure cap is closed and sealed, and shake well before use.
2. Mask off surfaces not intended to be treated.
3. Liberally apply an even coat of STONETECH® BulletProof Sealer using a paint pad, roller, brush or low-pressure sprayer.
4. Allow sealer to penetrate the surface for 10-15 minutes. During this time, keep the surface wet with sealer, adding more sealer as needed. DO NOT ALLOW SEALER TO COMPLETELY DRY ON THE SURFACE.
5. Thoroughly wipe dry the entire surface with clean absorbent towels.
6. A second coat may be needed for porous, absorbent surfaces. If a second coat is required, it should be applied within 30-40 minutes from the initial application as directed in steps 3-5.
7. Should a sealer residue appear, rewet the impacted section of the surface with sealer. Agitate the surface with a white nylon scrubbing pad to loosen residue and wipe dry with a clean, absorbent towel.
8. A full cure is achieved in 24-72 hours. Use of the treated surface may resume in 6-8 hours. If use of the surface must resume sooner, cover the treated surface with red rosin paper to protect it until full cure has been achieved.
9. Clean tools used during application with water.
Cleaning Clean tools used during application with water
MAINTENANCE Highly alkaline, acidic, ammoniated, or abrasive cleaners are not necessary for daily maintenance and may also degrade the STONETECH sealer used, adversely affecting stain resistance. Tile and stone routine cleaning with a neutral pH cleaner such as STONETECH Stone & Tile Cleaner is recommended. For tough or difficult to remove soil use STONETECH KlenzAll™ Cleaner, a nylon scrubbing pad or a long handled stiff bristle brush. Please note: Prior to using any cleaning material on a tile, stone, etc. installation, test a discrete area or scrap piece of tile to insure desired results. For additional information, please refer to the TDS 262 Stone and Tile Care Guide Guide.
